5ab14532

2.2. Diagnostics of malfunctions of coupling

Cause of defect

Elimination method
Coupling revolves (not completely joins) By sharp pressing an accelerator pedal the engine gains steam, but the car almost does not accelerate (it especially noticeable at the movement on rise); the smell of superheated frictional slips can be felt; fuel consumption increases

Oiling of a flywheel, press disk, frictional overlays of the conducted disk

Carefully wash out white spirit or gasoline greasy surfaces and dry wipe them. Replace strongly greasy conducted disk. Remove the cause of oiling (an oil leak through cuffs of the engine and/or transmission)

Strong wear or burning of frictional overlays of the conducted disk

Replace the conducted disk assembled

Decrease in effort of a diaphragm spring

Replace press a disk assembled with a casing (coupling "basket")

The piston of the main cylinder of the drive of coupling slowly comes back to a starting position because of swelling of rubber cuffs

Replace cuffs or the cylinder assembled. At suspicion in liquid of a hydraulic actuator of coupling replace it with hit of gasoline or other solvents

Coupling conducts (is not completely switched off) gear shifting of the forward course Is complicated, transfer of a backing joins with noise. The transmission is serviceable.

The wrong adjustment of the drive of coupling (the full speed of a pedal is small)

Adjust the drive. Replace the deformed clutch release fork lever

Air got to system of a hydraulic actuator (a pedal "soft")

Pump over system, tighten connections

Weakening of rivets or breakage of frictional slips, buckling of the conducted disk (a face beating more than 0,5 mm)

Replace a disk

Strong and uneven wear, teases on working surfaces of a flywheel or a press disk

Pierce or replace a flywheel. At damage of a surface of a press disk replace a casing with a press disk in collecting (coupling "basket")

Distortion or buckling of a press disk

Replace a casing with a press disk in collecting (coupling "basket")

Jamming of a nave of the conducted disk on vents of a main shaft of the transmission

Clear vents of dirt, eliminate small damages with a file. At considerable wear or damage of shliyets replace a disk and/or a main shaft of the transmission. Before assembly apply SHRUS-4 lubricant on vents

Jammed the release bearing

Replace the bearing

Strong wear of petals of a diaphragm spring in the place of contact with the release bearing

Replace a casing with a press disk in collecting (coupling "basket")

Coupling is not switched off (the pedal "fails")

The coupling switching off fork is strongly deformed or broken

Replace a fork

Air in system of a hydraulic actuator

Pump over system, tighten connections

Coupling is not switched off (the pedal "fails"). It is short-term it is possible to include coupling only sharp pressing a pedal

Strong wear, defects of a mirror of the main cylinder; dirt in the cylinder

Clean or replace the cylinder. At any service it is necessary to replace also its cuffs

Wear or defect of a cuff

Replace cuffs or the cylinder assembled

Breakthroughs at start-off

Jamming of a nave of the conducted disk on vents of a main shaft of the transmission

Clear vents of dirt, eliminate small damages with a file. At considerable wear or damage of shliyets replace a disk and/or a main shaft of the transmission. Before assembly apply SHRUS-4 lubricant on vents

Deformation of the conducted disk

Replace the conducted disk

Weakening of fastening of frictional overlays of the conducted disk, strong wear or cracks on slips

Replace the conducted disk

Loss of elasticity of spring plates of the conducted disk

Replace the conducted disk

Considerable draft or breakage of springs of a quencher of tortional fluctuations, wear of windows under springs

Replace the conducted disk

Teases on working surfaces of a flywheel or a press disk

Replace a flywheel or a casing of coupling with a press disk in collecting (coupling "basket")

Jingle, knock or noise at coupling inclusion

Considerable draft or breakage of springs of a quencher of tortional fluctuations, wear of windows under springs

Replace the conducted disk

Deformation of the conducted disk

Replace the conducted disk

Weakening of fastening of frictional overlays of the conducted disk, strong wear or cracks on slips

Replace the conducted disk

Jingle, knock or noise at coupling inclusion

Wear, damage of the release bearing or absence of lubricant in it

Replace the bearing

Coupling pedal scratch

Plastic plugs of a pedal are not greased

Grease Litolom-24 or SHRUS-4 plugs

Plastic plugs of a pedal are strongly worn-out

Replace plugs, before installation grease them with Litolom-24 or SHRUS-4

After a coupling pedal otpuskaniye it does not come back to a starting position

Air in system of a hydraulic actuator

Pump over system, tighten connections

Lost elasticity or the returnable spring of a pedal is broken

Replace a spring